#08007 LS-2017-2018 Tunnel Shield NEW!

size 12.5” x 41.25” – stainless

ALSO – Don’t forget to cover sensor wires to protect against too much heat… with Koolsleeve black 900°F fiberglass sleeve. It will stop burns. (see sleeve area)

(fits 2017 to present)

#08002 C3 Comp Coupe Viper 2500°F

           Side Exhaust heat shields

size 19″ x 40″ – set (2) with 10 stainless straps – stainless

Vipers are very powerful cars and generate a lot of heat. This stainless product is an excellent way to control extreme heat. It  has very low heat transference with a high temperatue ceramic inside and will tolerate direct contact with heat sources such as catalytic converters. Its high melting point (3000 plus degrees) and outstanding radiant heat reflection make it the material of choice. In the Viper application, it is intended to wrap tightly around the factory or an aftermarket exhaust system and block the considerable sill heat at its source. The resultant air gap between the shield and sill’s first surface helps as well. This material is commonly used at the highest levels of motor sports and aerospace.

#08003 94-to present Viper GTS & RT-10

            Side Exhaust heat shields

size 09″ x 48″- set (2) with 10 stainless straps – stainless

Vipers are very powerful cars and generate a lot of heat. This stainless product is an excellent way to control extreme heat. It has very low heat transference with a high temperature ceramic inside and will tolerate direct contact with heat sources such as catalytic converters. Its high melting point (3000 plus degrees) and outstanding radiant heat reflection make it the material of choice. In the Viper application, it is intended to wrap tightly around the factory or an aftermarket exhaust system and block the considerable sill heat at its source. The resultant air gap between the shield and sill’s first surface helps as well. This material is commonly used at the highest levels of motor sports and aerospace.

HEATMASTER ……HOW TO MEASURE

Unlike shields you buy that wrap around mufflers or pipes which have no guts….and will in a matrer of days heat up…and you will have the same problem…..

The Heatmaster has a 3000°F. stainless outside and a 2500°F. Ceramic inside that you can touch and torch at the same time and not burn your hands. These are the same shields we make for the NASCAR teams today. The shield is .003 stainless with a lenghwise line design in the material with grommets evenly spaced for easy installation with stainless tie straps. (below) This shield reduces extreme heat to interiors and machanical objects.

When measuring for the Heatmaster exhaust shield. you want to cover the top and 1/2 half way on both  sides leaving the bottom open so the heat came excape to another area. Heat build up can distroy your exhaust so it is important that the heat does not go up (that’s why we are covering the top) and it leaves through the bottom. To order call 1-877-566-5369 we need the length and the width. Grommets will be on both long sides evenly spaced for easy installation and the straps sizes are below. Special notes can be faxed over to us at 1-704-662-9109 to Pat. Stainless tie straps are below…3 sizes available

NEED WIDTH and LENGTH……………for order. 877-566-5369 see Pat

 STAINLESS TIE STRAPS 

#09025 Stainless Tie Strap – size 14″ x 1/4″

#09026 Stainless Tie Strap – size 8″ x 1/4″ 

#09027 Stainless Tie Strap – size 26″ x 1/4″

#08005 for 63-82 Corvette – Side Exhaust Shields

Polished 

#08009P Cobra 28” w/ S cut on end/Polished

1-set of 4″ x 28″ stainless outer shields with an “S” cut at the end. 2 liners with a 2500°F. a ceramic inside insulation. 2 header wrap strips to protect from scratches on pipes and 2 stainless clamps to hold on pipes and keep liners in place. fits 4″ pipes.

The “S” cut is designed to fit closer at the end where the pipe curves by the back wheel.

Shield size 4.5″ x 28″- stainless

fits 4” pipe            CAll 877-566-5369 or email us for your questions or order to Pat at sales@koolmat.com