STOP BURNING BOOTS!!

 

Tie Rod/Ball Joint/Sway Bar
Boot Shield Insulation Kit

Used to stop heat from melting rubber boots in road racing cars. 14 Die cut strips grommeted on both ends for easy installations with black UV tie straps (supplied with kit). Comes with instructions. Available for Corvette and Viper.
Part # 07064  $99.65

 

STOP BOOTS FROM MELTING W/ KOOLMAT’S “KOOLBOOTS"

Corvette/Viper/Cadillac Boot Insulation Kit
For Hi-Speed/Hi-Heat Road Racing Vehicles

Warning: The installation of this kit requires the vehicle to be elevated.? Use a properly rated jack, jack stands or vehicle lift and ensure all proper safety measures are in place before working beneath the vehicle.? It is the installer’s responsibility to follow all manufacturers’ safety recommendations when servicing the vehicle.

Installation Instructions

Elevate and secure the vehicle with suitable jack stands. NEVER WORK UNDER OR NEAR AN AUTOMOBILE UNLESS PROPERLY SUPPORTED. ?Remove the wheel to access the suspension boots.

*** Note instructions show the rotors removed for clarification only.? Rotor removal is NOT required. *Pt No. # 07064............Kit Contents

 

Part Number

QTY

Description

 

?TR

4

Front and Rear Tie Rod Boot Shield

RL

2

Rear Lower Ball Joint Boot Shield

RU

2

Rear Upper Ball Joint Boot Shield

LSBL

1

Left Lower Sway Bar Boot Shield

LSBR

1

Right Lower Sway Bar Boot Shield

FU

2

Front Upper Ball Joint Boot Shield

FL

2

Front Lower Ball Joint Boot Shield

Tie Straps 7"

8

Black UV Stabilized Tie Straps

Tie Straps 14"

6

Black UV Stabilized Tie Straps

Instructions

1

Installation Instructions

 

(Metal Tie straps are available upon request when heat gets too hot for plastic tie straps)

 

Install the shields with the woven side out.? Insert the tie strap through the grommets and pull till snug.? Use the long tie straps on the upper ball joint shields fastened as shown in figures 1-4 and the Lower Sway bar shields.

 

Front Upper Shield

   

                          Figure 1                                                             Figure 2

                   Install with Fabric Out                        Insert Strap through grommets and

                   Ref pn. FU                                        over “Upper A-ARM"

 



 

Tie Rod/Ball Joint/Sway Bar
Boot Shield Insulation Kit

Used to stop heat from melting rubber boots in road racing cars. 14 Die cut strips grommeted on both ends for easy installations with black UV tie straps (supplied with kit). Comes with instructions. Available for Corvette and Viper.
Part # 07064  $150.40

New 67 - 69 Camaro KoolMat kit
New Shifter Boot Insulation Kit
New 53 - 58 Magnette Kit

 

Custom Cut Koolmat Floor Insulation Kits
These kits are cut from Koolmat Insulation material and are made to fit the car properly with no gaps. A tube of Valco Cincinnatiís silicone is provided to seal the kit before carpeting.
 
Description Kit Size Retail Price
97211 Viper Comp Coupe 7 pcs $378.84
97209 Cobra Factory 5 21 pcs $675.14
97210 Cobra F-5 Back Wall 4 pcs $241.93
97201 LS-1 Front 9 pcs $515.75
97202 LS-1 Bulkhead Kit 2 pcs $283.55
97200 LS-1 Rear 13 pcs $566.75
97212 Jeep CJ-8 Scrambler 11 pcs $302.91
97205 Mustang 73-98 9 pcs $375.35
97206 T-Bird 55-57 8 pcs $442.45
97207 Jaguar XKE 20 pcs $419.46
97227 Austin Healy 3000 7 pcs $513.49
97216 MGA 1600 Mk II 21 pcs $691.21
LS-1 Installation Pics!
These kits are available through our dealers. See Distributor list page for ordering or email and request more information on how to become a Koolmat Insulation dealer.


"STOP VAPOR LOCK"!
New Motorcycle Fuel Line Sleeve.
Part # 09202C  25" Long


 


D & H Heat Technology, Inc.
P.O. Box 985
Mooresville, NC  28115
Fax: 704.662.9109
Phone: 704.662.9099
Toll Free: 877.566.5369
sales@koolmat.com